New machine with a slight leak

Did you have an issue or question about operation of your Dream T tank machine on Day One right out of the box? If so, report it here and also keep us abreast of the resolution.
Post Reply
cn80
Americano
Posts: 5
Joined: Sun Jul 22, 2018 8:26 am
Location: Wiltshire

New machine with a slight leak

Post by cn80 » Sun Jul 22, 2018 12:03 pm

Hello everyone just got a dream t delivered and set it up but noticed a small leak can anyone tell me where it's coming from and how to fix it please.
Attachments
Screenshot_20180722-165851~2.jpg

goodboyr
God Shot
Posts: 226
Joined: Thu Jan 10, 2013 10:05 pm
Location: Canada

Re: New machine with a slight leak

Post by goodboyr » Sun Jul 22, 2018 2:40 pm

It looks like it's coming from one of the small Teflon lines going into brew boiler. Remove the top panel and look down from top. This is a quick connect push in fitting that depends on a clean end cut on the Teflon and a fully pushed in connection. It's also easy to nick these lines causing a leak. All will be revealed when you look down from the top.

Sent from my SM-G950W using Tapatalk

Bob
La Spaziale Dream and Baratza Sette 270W

cn80
Americano
Posts: 5
Joined: Sun Jul 22, 2018 8:26 am
Location: Wiltshire

Re: New machine with a slight leak

Post by cn80 » Sun Jul 22, 2018 3:30 pm

Thanks for your reply I will take a look as you said

cn80
Americano
Posts: 5
Joined: Sun Jul 22, 2018 8:26 am
Location: Wiltshire

Re: New machine with a slight leak

Post by cn80 » Mon Jul 23, 2018 10:05 am

I have pictured where the leak is coming from its the clear pipe in the middle you can see a drip forming.
Any ideas?
Attachments
Screenshot_20180723-145908~2.jpg
Screenshot_20180723-145908~2.jpg (78.05 KiB) Viewed 357 times

goodboyr
God Shot
Posts: 226
Joined: Thu Jan 10, 2013 10:05 pm
Location: Canada

Re: New machine with a slight leak

Post by goodboyr » Mon Jul 23, 2018 10:44 am

Ok. As suspected it's a small Teflon tube connection. The brass connection has a thin collar. Depower and shut off water to machine. If you push the collar back towards the fitting, while pulling on the tube, you can pull the tube out. Inspect the end of the tube for a clean, perpendicular cut. If the end isn't cut straight and you have enough slack in the tube, make a clean cut, then push the tube all the way into the fitting until it stops. That should fix the leak.

Sent from my SM-G950W using Tapatalk




Bob
La Spaziale Dream and Baratza Sette 270W

cn80
Americano
Posts: 5
Joined: Sun Jul 22, 2018 8:26 am
Location: Wiltshire

Re: New machine with a slight leak

Post by cn80 » Mon Jul 23, 2018 10:57 am

Thanks goodboyr after a bit of fiddling it seems to have stopped leaking even after pulling a few shots.
It seems that that tube feeds the gauge and when pulling a shot the gauge does not move on the left side which is the brew pressure gauge the left gauge which is I'm assuming the steam pressure is working fine.
See pic.
Many thanks for your help so far.
Attachments
Screenshot_20180723-155149.jpg
Screenshot_20180723-155149.jpg (78.63 KiB) Viewed 356 times

cn80
Americano
Posts: 5
Joined: Sun Jul 22, 2018 8:26 am
Location: Wiltshire

Re: New machine with a slight leak

Post by cn80 » Mon Aug 13, 2018 4:49 pm

Can anybody advise?

Post Reply

Return to “Dream T Day One Issues”