weird high pressure after water pressure regulator install

General questions, comments, and discussions about the Plumbed Dream machine. New owners post your impressions of your Dream - likes, dislikes, and any other comments.
Post Reply
cofex
Americano
Posts: 9
Joined: Tue Nov 03, 2015 8:46 pm
Location: florida

weird high pressure after water pressure regulator install

Post by cofex »

Hi,

I have a La Spaziale Dream plumbed in on the water from the fridge 1/4 line. I used it without an water pressure regulator for 3 years.
The pressure on idle is reading 4.2bars.

I installed a water pressure regulator, in fact I installed 2, just to make sure,
Watts 1/4 LF 263A and Watts 1/4 LF560G

During usage, the water is around 1.5 bars, goes to 9.5bars when I run an espresso shot and goes back to 1.5 bars

When I start the machine, the water pressure goes to 6-6.5 bars and throws an alert for high pressure. it stays on 6.5 and it goes slowly down to 1.5 after the temperature gets to be stable, in around 10 minutes.

From reading through the forums it seems the pressure regulator is supposed to let some of the initial pressure to be absorbed back into the house water pressure. Not sure. Both regulators are Watts, are supposed to be good.

The questions I have:

1. Is this normal?
2. Should I stop using a pressure regulator given that the machine is stable without one?

Thank you...
Cofex
La Spaziale Dream v 1.20
Baratza Vario, Custom Gaggia Classic (PID + Invensys Pump)

User avatar
chas
Vivaldi Dreamer
Posts: 3044
Joined: Wed Jun 02, 2004 11:52 pm
Location: Central Maryland
Contact:

Re: weird high pressure after water pressure regulator install

Post by chas »

If I read your signature block correctly, your machine is running SW version 1.20. I have version 1.24 on mine but there may be an even later version. At any rate I think ver 1.24 addresses the issue you are seeing.

You may want to contact your machine supplier to see if they have a newer version they can get to you.
Chas
LM GS/3 & LaSpaziale Dream v 1.25 (US 120V)
Mazzer Kony E, Customized Rocky
Hottop P/B
cofex
Americano
Posts: 9
Joined: Tue Nov 03, 2015 8:46 pm
Location: florida

Re: weird high pressure after water pressure regulator install

Post by cofex »

Thank you Chas,

I called Chris coffee

they said, the issue is well know: the sensor is too delicate and triggers for any big pressure variation.

At the start of the machine, the sensor detects water pressure change and triggers an alert for high pressure.

This is an issue with a lot of La spaziale machines.

They said to upgrade to the latest firmware 1.24, and to disable the water sensor.

other than that: they suggest to set the preinfusion to 3 seconds and 25 psi and 9 bars for the espresso.

I hope this info helps others.

Thank you for your help.
Cofex
La Spaziale Dream v 1.20
Baratza Vario, Custom Gaggia Classic (PID + Invensys Pump)

goodboyr
Barista
Posts: 255
Joined: Thu Jan 10, 2013 10:05 pm
Location: Canada

Re: weird high pressure after water pressure regulator install

Post by goodboyr »

And in case you are looking for the 1.24 file:

https://www.s1cafe.com/viewtopic.php?p=25517#p25517

Sent from my SM-G973W using Tapatalk

Bob
La Spaziale Dream and Baratza Sette 270W
cofex
Americano
Posts: 9
Joined: Tue Nov 03, 2015 8:46 pm
Location: florida

Re: weird high pressure after water pressure regulator install

Post by cofex »

Thank you for the upgrade file, cc sent it by email as well

Thanks a lot, this high pressure alert was driving me crazy :bounce:

...
Cofex
La Spaziale Dream v 1.20
Baratza Vario, Custom Gaggia Classic (PID + Invensys Pump)

Post Reply

Return to “Dream General Q&A”